Browse Source

Merge remote-tracking branch 'remotes/github_ntruchsess/attiny'

timer1
Youen Toupin 8 years ago
parent
commit
c819cfdf17
  1. 39
      LowLevel.h
  2. 16
      OneWireSlave.cpp
  3. 1
      OneWireSlave.h

39
LowLevel.h

@ -21,6 +21,43 @@
#define DIRECT_WRITE_LOW(base, mask) ((*((base)+2)) &= ~(mask))
#define DIRECT_WRITE_HIGH(base, mask) ((*((base)+2)) |= (mask))
#if defined (__AVR_ATtiny85__)
#define CLEARINTERRUPT GIFR |= (1 << INTF0)
#include "UserTimer.h" //ATtiny-support based on TinyCore1 Arduino-core for ATtiny at http://github.com/Coding-Badly/TinyCore1.git
__attribute__((always_inline)) static inline void UserTimer_Init( void )
{
UserTimer_SetToPowerup();
UserTimer_SetWaveformGenerationMode(UserTimer_(CTC_OCR));
}
__attribute__((always_inline)) static inline void UserTimer_Run(short skipTicks)
{
UserTimer_SetCount(0);
UserTimer_SetOutputCompareMatchAndClear(skipTicks);
UserTimer_ClockSelect(UserTimer_(Prescale_Value_64));
}
#define UserTimer_Stop() UserTimer_ClockSelect(UserTimer_(Stopped))
#elif defined (__AVR_ATmega328P__)
#define CLEARINTERRUPT EIFR |= (1 << INTF0)
#define USERTIMER_COMPA_vect TIMER1_COMPA_vect
__attribute__((always_inline)) static inline void UserTimer_Init( void )
{
TCCR1A = 0;
TCCR1B = 0;
// enable timer compare interrupt
TIMSK1 |= (1 << OCIE1A);
}
__attribute__((always_inline)) static inline void UserTimer_Run(short skipTicks)
{
TCNT1 = 0;
OCR1A = skipTicks;
// turn on CTC mode with 64 prescaler
TCCR1B = (1 << WGM12) | (1 << CS11) | (1 << CS10);
}
#define UserTimer_Stop() TCCR1B = 0
#endif
#elif defined(__MK20DX128__) || defined(__MK20DX256__)
#define PIN_TO_BASEREG(pin) (portOutputRegister(pin))
#define PIN_TO_BITMASK(pin) (1)
@ -110,7 +147,7 @@ public:
inline void attachInterrupt(void (*handler)(), int mode)
{
EIFR |= (1 << INTF0); // clear any pending interrupt (we want to call the handler only for interrupts happending after it is attached)
CLEARINTERRUPT; // clear any pending interrupt (we want to call the handler only for interrupts happending after it is attached)
::attachInterrupt(interruptNumber_, handler, mode);
}
inline void detachInterrupt() { ::detachInterrupt(interruptNumber_); }

16
OneWireSlave.cpp

@ -31,7 +31,6 @@ OneWireSlave OWSlave;
byte OneWireSlave::rom_[8];
byte OneWireSlave::scratchpad_[8];
Pin OneWireSlave::pin_;
byte OneWireSlave::tccr1bEnable_;
unsigned long OneWireSlave::resetStart_;
unsigned long OneWireSlave::lastReset_;
@ -69,9 +68,9 @@ void(*OneWireSlave::singleBitSentCallback_)(bool error);
void(*OneWireSlave::logCallback_)(const char* message);
ISR(TIMER1_COMPA_vect) // timer1 interrupt
ISR(USERTIMER_COMPA_vect) // timer1 interrupt
{
TCCR1B = 0; // disable clock
UserTimer_Stop(); // disable clock
void(*event)() = timerEvent;
timerEvent = 0;
event();
@ -99,10 +98,7 @@ void OneWireSlave::begin(const byte* rom, byte pinNumber)
pin_.writeLow(); // make sure the internal pull-up resistor is disabled
// prepare hardware timer
TCCR1A = 0;
TCCR1B = 0;
TIMSK1 |= (1 << OCIE1A); // enable timer compare interrupt
tccr1bEnable_ = (1 << WGM12) | (1 << CS11) | (1 << CS10); // turn on CTC mode with 64 prescaler
UserTimer_Init();
// start 1-wire activity
beginWaitReset_();
@ -241,15 +237,13 @@ void OneWireSlave::setTimerEvent_(short delayMicroSeconds, void(*handler)())
short skipTicks = (delayMicroSeconds - 3) / 4; // round the micro seconds delay to a number of ticks to skip (4us per tick, so 4us must skip 0 tick, 8us must skip 1 tick, etc.)
if (skipTicks < 1) skipTicks = 1;
TCNT1 = 0;
OCR1A = skipTicks;
timerEvent = handler;
TCCR1B = tccr1bEnable_;
UserTimer_Run(skipTicks);
}
void OneWireSlave::disableTimer_()
{
TCCR1B = 0;
UserTimer_Stop();
}
void OneWireSlave::onEnterInterrupt_()

1
OneWireSlave.h

@ -103,7 +103,6 @@ private:
static byte rom_[8];
static byte scratchpad_[8];
static Pin pin_;
static byte tccr1bEnable_;
static unsigned long resetStart_;
static unsigned long lastReset_;

Loading…
Cancel
Save